各位高手,请教一下,新手学zemax编程,照着敲了一段
程序,在zemax中ZPL程序为什么运行不了,还请各位高手指点指点,谢谢!
#WufZ18# zWIeHIt
V(mnyI ek)Xrp:2
97!5Q~I 40K2uT{cq
9P"iuU PZM42"[&
^7u#30,}3~ gfo}I2"
$a.u05 O&$0&dhc
s AE9<(g&@ q)iTn)Z! ZPL程序代码如下:
3] 76fF\^[ H(qm>h$bU ! ex30401
<qY5SV, ! This program shows how to create a doublet from scratch
QN
G& p4mY0Y]mP ! set system parameters
;$!I&<) SYSP 30, 0 # set lens unit as mm
Q4K+*Fi} nj2gs,k SYSP 10, 0 # set system aperture as Entrance Pupil Diameter
K$-;;pUl SYSP 11, 50 # set system aperture value as 50mm
|.w;r
V}9;eJRvw SYSP 201, 3 # set total wavelength number as 3
/V^sJ($V$~ SYSP 202, 1, 0.48613270 # set the 1st wavelength as 0.48613270 micron
e@jfIF0=} SYSP 202, 2, 0.58756180 # set the 2nd wavelength as 0.58756180 micron
;~/4d- SYSP 202, 3, 0.65627250 # set the 3rd wavelength as 0.65627250 micron
!N~*EI$ SYSP 203, 1, 1 # set the 1st wavelength weight as 1
E`xU m9F SYSP 203, 2, 1 # set the 2nd wavelength weight as 1
Y';>O ` SYSP 203, 3, 1 # set the 3rd wavelength weight as 1
zj20;5o>U& <t}? $1 SYSP 200, 2 # set the 2nd wavelength as the primary wavelength
UqtHxEI%R~ f\}22}/ SYSP 100, 0 # set the field type as angle
POGw`:)A SYSP 101, 3 # set the total field number as 3
#nEL~& SYSP 102, 1, 0 # set field 1 as x=0 degree
i6>R qP!69 SYSP 103, 1, 0 # set field 1 as y=0 degree
d=F-L SYSP 104, 1, 1 # set field 1 as weight=1
yGEb7I$h SYSP 102, 2, 0 # set field 2 as x=0 degree
}O*WV 1 SYSP 103, 2, 3.5 # set field 2 as y=3.5 degree
Efr&12YSS SYSP 104, 2, 1 # set field 2 as weight=1
;Qa;@ SYSP 102, 3, 0 # set field 3 as x=0 degree
y Nva1I SYSP 103, 3, 5 # set field 3 as y=5 degree
\dV Too SYSP 104, 3, 1 # set field 3 as weight=1
"DjU:*' 9#@Zz4Ww ! set surface 1 as stop
8p=>?wG STOPSURF 1
oVkr3KZ e1P7
.n} ! insert 3 surfcaces after stop
E1W:hGI INSERT 2
{A3m+_8 INSERT 2
V2Y$yV8g1 INSERT 2
]kS7n@8 YMu) ! set surface parameters
d@>\E/zA SURP 1, THIC, 275 # set surface 1 thickness as 275
H8i+'5x,? O71BM@2< SURP 2, TYPE, "STANDARD" # set surface 2 type as "STANDARD",can be omitted
ragSy8M SURP 2, COMM, "front f1" # set surface 2 comment
1nB@zBQu- SURP 2, CURV, 1/600 # set surface 2 curvature as 1/600
z%};X$V`J SURP 2, THIC, 18 # set surface 2 thickness as 18
`Zf9$K| SURP 2, GLAS, "BK7" # set surface 2 glass type as BK7
7;xKy'B\ P<L&c_u SURP 3, COMM, "back f1/front f2" # set surface 3 comment
!$r9C/k SURP 3, CURV, -1/115 # set surface 3 curvature as -1/115
J @B4
R&V SURP 3, THIC, 18 # set surface 3 thickness as 18
:t>Q:mX(N SURP 3, GLAS, "F2" # set surface 3 glass type as F2
*Sb2w*c> q6&67u0 SURP 4, COMM, "back f2" # set surface 4 comment
b-nY xd SURP 4, CURV, -1/243 # set surface 4 curvature as -1/243
HRHrSf7 SURP 4, THIC, 395 # set surface 4 thickness as 395
;*QN9T=0 !!+Da> UPDATE