各位高手，请教一下，新手学zemax编程，照着敲了一段
程序，在zemax中ZPL程序为什么运行不了，还请各位高手指点指点，谢谢！
)e]:T4*vo !)_5 z < 
l. b QAcvv 0Hv 
vjbot^W9 R)G'ILneV 
,cgC_ % &[JI L=m5 
4Mg0 9 "eGS~- DVK 
M,y='* \M 4zfgtg( 
/sJk[5!z hoSk ZPL程序代码如下：
t_P1a0Zu <}B|4($ ! ex30401
HHtp.; L/ ! This program shows how to create a doublet from scratch
v }P~g
xAz gQ ! set system parameters
^<s X^V+{ SYSP 30, 0 # set lens unit as mm
,gD30Pylz cF,u)+2b|6 SYSP 10, 0 # set system aperture as Entrance Pupil Diameter
[o|]>(tk SYSP 11, 50 # set system aperture value as 50mm
Ya\G/R t41\nTZr SYSP 201, 3 # set total wavelength number as 3
x-Xb4?{ SYSP 202, 1, 0.48613270 # set the 1st wavelength as 0.48613270 micron
(;Lz `r' SYSP 202, 2, 0.58756180 # set the 2nd wavelength as 0.58756180 micron
L{
.r8wSrI SYSP 202, 3, 0.65627250 # set the 3rd wavelength as 0.65627250 micron
PS \QbA
SYSP 203, 1, 1 # set the 1st wavelength weight as 1
r] 8tl SYSP 203, 2, 1 # set the 2nd wavelength weight as 1
{jlm]< :&Z SYSP 203, 3, 1 # set the 3rd wavelength weight as 1
o&I 0*~ sN 5Ko "- SYSP 200, 2 # set the 2nd wavelength as the primary wavelength
EKwS~G.b! s?OGB} SYSP 100, 0 # set the field type as angle
Uf_w
o SYSP 101, 3 # set the total field number as 3
&QCqaJ- SYSP 102, 1, 0 # set field 1 as x=0 degree
SHz& o[u SYSP 103, 1, 0 # set field 1 as y=0 degree
NP%ll e,l SYSP 104, 1, 1 # set field 1 as weight=1
f
( UcJx SYSP 102, 2, 0 # set field 2 as x=0 degree
x40R)Le d SYSP 103, 2, 3.5 # set field 2 as y=3.5 degree
EEaKT`/d SYSP 104, 2, 1 # set field 2 as weight=1
Uc7X) SYSP 102, 3, 0 # set field 3 as x=0 degree
oHeo]<Fbv SYSP 103, 3, 5 # set field 3 as y=5 degree
jY ^ndr0; SYSP 104, 3, 1 # set field 3 as weight=1
(m.]0v*&c |Zkcs]8M! ! set surface 1 as stop
2LD4f[a; STOPSURF 1
i.K}(bo;b dqd Qt_ ! insert 3 surfcaces after stop
YMqL,& Q{1 INSERT 2
azOp53zR INSERT 2
ojyG|Y INSERT 2
5 z El`h r("7
X2f ! set surface parameters
KJ'MK~g SURP 1, THIC, 275 # set surface 1 thickness as 275
_jeub [ #1m!,t C SURP 2, TYPE, "STANDARD" # set surface 2 type as "STANDARD",can be omitted
qJISB7F[%O SURP 2, COMM, "front f1" # set surface 2 comment
%NxNZe SURP 2, CURV, 1/600 # set surface 2 curvature as 1/600
wl(}F^:/` SURP 2, THIC, 18 # set surface 2 thickness as 18
@X4; fd SURP 2, GLAS, "BK7" # set surface 2 glass type as BK7
p aMw88*u !km o% + SURP 3, COMM, "back f1/front f2" # set surface 3 comment
rZ0@GA SURP 3, CURV, -1/115 # set surface 3 curvature as -1/115
A3 j>R477A SURP 3, THIC, 18 # set surface 3 thickness as 18
+{Q\B}3cj1 SURP 3, GLAS, "F2" # set surface 3 glass type as F2
'OF)`5sj _$Z46w HmB SURP 4, COMM, "back f2" # set surface 4 comment
[nG/>Z]W SURP 4, CURV, -1/243 # set surface 4 curvature as -1/243
2.; OHQTE SURP 4, THIC, 395 # set surface 4 thickness as 395
ncS^NH(& ixfkMM ,W UPDATE
