各位高手,请教一下,新手学zemax编程,照着敲了一段
程序,在zemax中ZPL程序为什么运行不了,还请各位高手指点指点,谢谢!
w~66G ">H*InF
~7]V^tG c!6D{(sfh
]eL# bJ EZUaYp~M
v] m/$X2 ~ ld.I4
+}:Z9AAMy qE)FQeN
?
wS}' #AD_EN9
E]V,
@ \""^'pP@ ZPL程序代码如下:
e5L+NPeM6v cx\"r ! ex30401
]J7qsMw ! This program shows how to create a doublet from scratch
3?93Pj3oPt YI0
wr1N ! set system parameters
mF7Ak&So^ SYSP 30, 0 # set lens unit as mm
9CDei~ wuqe{? SYSP 10, 0 # set system aperture as Entrance Pupil Diameter
jPh<VVQ$@ SYSP 11, 50 # set system aperture value as 50mm
8v$q+Wic ^C>kmo3J SYSP 201, 3 # set total wavelength number as 3
hRkCB SYSP 202, 1, 0.48613270 # set the 1st wavelength as 0.48613270 micron
eg[EFI.h SYSP 202, 2, 0.58756180 # set the 2nd wavelength as 0.58756180 micron
j7I=2xnTWu SYSP 202, 3, 0.65627250 # set the 3rd wavelength as 0.65627250 micron
vhe Y
F@ SYSP 203, 1, 1 # set the 1st wavelength weight as 1
K~(RV4oF8B SYSP 203, 2, 1 # set the 2nd wavelength weight as 1
pbMANZU[ SYSP 203, 3, 1 # set the 3rd wavelength weight as 1
=
0 ~4k# {*xE+ | SYSP 200, 2 # set the 2nd wavelength as the primary wavelength
4n,&,R r# w2LnY1A SYSP 100, 0 # set the field type as angle
fNNl1Vls SYSP 101, 3 # set the total field number as 3
F`D$bE;| SYSP 102, 1, 0 # set field 1 as x=0 degree
$|$@?H>K SYSP 103, 1, 0 # set field 1 as y=0 degree
zIa={tU SYSP 104, 1, 1 # set field 1 as weight=1
@Q1!xA^S SYSP 102, 2, 0 # set field 2 as x=0 degree
-]3 K#M)s SYSP 103, 2, 3.5 # set field 2 as y=3.5 degree
~j!n`#.\ SYSP 104, 2, 1 # set field 2 as weight=1
AR |4^ SYSP 102, 3, 0 # set field 3 as x=0 degree
a%#UF@I SYSP 103, 3, 5 # set field 3 as y=5 degree
h,LSqjf" SYSP 104, 3, 1 # set field 3 as weight=1
]E9iaq6Z ieyK$q ! set surface 1 as stop
=!TUf/O- STOPSURF 1
-}7$;QK&a BMp'.9Qgm ! insert 3 surfcaces after stop
%"
iX3 INSERT 2
I~7iIUD INSERT 2
Nl\`xl6y] INSERT 2
86#l$QaK{ :WB uU ! set surface parameters
7?dWAUF SURP 1, THIC, 275 # set surface 1 thickness as 275
c>bns/f zTng]Mvx SURP 2, TYPE, "STANDARD" # set surface 2 type as "STANDARD",can be omitted
3kxo1eb
SURP 2, COMM, "front f1" # set surface 2 comment
3lF"nv SURP 2, CURV, 1/600 # set surface 2 curvature as 1/600
&bTCTDZh SURP 2, THIC, 18 # set surface 2 thickness as 18
4\z@Evm SURP 2, GLAS, "BK7" # set surface 2 glass type as BK7
&2ED<%hH` [8QK @5[ SURP 3, COMM, "back f1/front f2" # set surface 3 comment
hBU)gP75 SURP 3, CURV, -1/115 # set surface 3 curvature as -1/115
7}iv+rQ SURP 3, THIC, 18 # set surface 3 thickness as 18
V.Hv6 SURP 3, GLAS, "F2" # set surface 3 glass type as F2
;L-=z]IR, #*h\U]=VS SURP 4, COMM, "back f2" # set surface 4 comment
9evr!=": SURP 4, CURV, -1/243 # set surface 4 curvature as -1/243
+tPBm{| SURP 4, THIC, 395 # set surface 4 thickness as 395
x/,;:S CX]1I|T5 UPDATE