| zz1983 |
2009-07-14 09:55 |
高频炉选型知识介绍
一、透热、焊接类设备 Passes the fever,then welding class equipment 44F`$.v96
]C:l,I
频率在16KHZ左右，可透热Φ80左右工件，可焊接多种硬质合金刀具。 r{rQu-|.
C|?o*fQ
1、标准件、紧固件的热镦。 S*,rGCt'T
2、钎钢、钎具是回火、锻造、挤压等的加热。 izx#3u$P
3、金刚石锯片、钻具的焊接。 Y p:KI7
4、钎头、煤钻头、铆杆钻头、截齿的焊接。 %3$*K\Ai
5、车刀、刨刀、铣刀和各种木工刀具的焊接。 ]7/
b/J
iIP8`!
O
The frequency about 16KHZ the permeabIe feverΦ60 about work Piece,mayweld many kinds of hard aIloy tools K/}rP[H
HX6Ma{vBk
1、the standard Piece.the faslener heat upset Y}vr>\
2、drill rod steel，drill rod utensil drawing-back,forge,squeeze the warmup waiting bk\yCt06y;
3、Welding of diamond saw．drilling tool nM0[P6p
4、Bit,coal aiguille,rivetting the pole aiguille,welding of the pick I Ecf
5、Lathetool,planer tool,milling cutter and welding of different woodwork cutters d`(@_czdF
d`/tE?Gw
二、淬火类设备 Quenching class equipment zH*KYB
~jb"5CX
频率在30KHZ左右，小者可淬Φ10左右高精度小轴，淬硬层保持1.5mm以内，可淬Φ250直径大轴，也可淬Φ500左右齿轮。 1Zi,b
FE J~k1z
1、汽车配件、摩托车配件的淬火处理。 |eWjYGwJa
2、机械零件的热处理。如各种齿轮、链轮、各种轴、花健轴、销等的淬火处理。 7k( Kq5w.
3、机床行业的机床床面导轨的淬火处理。 ku..a G`
4、钳子、扳手、旋具、锤子、斧头等的热处理。 /AQMFx4-5
:hI@AA>g
The frequency about 30KHZ small may quench Φ10 about the high accuracy axis,the hard level maintains in 1 mm,may quench ￠250 the diameter macro-axis,also may quench Φ500 about the gear. LvEnX S
W
mm4hkf
1、Quenching of The car fittings，the motorcycle fittings are dealt with 5j-]EJb
2、Metal parts heat treatment. If each kind of gear,the chain wheel,each kind of axis,the spline shaft,sell and so on quen > B>CB3 U
ching Processing. 1NcCy! +
3、Engine bed profession engine bed surface of bed guide rail quenching processing oaK%Ww6~
4、the pliers,the spanner,turn on lathe have,the hammer,the axe Prime heat treatment c hEn |>~
W y%s1iu
三、退火类设备 Annealing class equipment y7|P-3[ 4w
}E7:ihy
可对各种机械零件进行整体或局部退火处理。 a:_I
可对Φ300直径不锈钢容器进行拉伸退火。 ts8+V<g
|> _!eS\=<
May carry on the whole or the spot annealing to each kind of machine parts processes XJ Iv1s\g
May carry on the annealing stretch Φ3300 the diameter steel vessel VnT>K9&3
A Z{^o4<q
（文章转载于网络，作者：党保强）
|
|