| yuanch1982 |
2022-04-01 11:09 |
zemax中zpl程序问题
各位高手，请教一下，新手学zemax编程，照着敲了一段程序，在zemax中ZPL程序为什么运行不了，还请各位高手指点指点，谢谢！ *U( 1iv0 n
s4!|v`+$M
[attachment=111852] V;M3z9xd
^nG1/}
[attachment=111853] ;5&k /CB1
\a {Aa
[attachment=111856] i)A`Vpn
}T?i%l
[attachment=111855] p=:7 atE
h <PYE]?l
[attachment=111854] Yt\E/*%
gubb .EY
[attachment=111857] _Ym&UY.u#
J`U $b+q6
ZPL程序代码如下： daaga}]d
e k Y?
! ex30401 1C^HCIH7J
! This program shows how to create a doublet from scratch Ws2prh^e(
/ig^7+ #
! set system parameters T=hm#]
SYSP 30, 0 # set lens unit as mm &xPOp$Sx~
GM34-G H+
SYSP 10, 0 # set system aperture as Entrance Pupil Diameter T{5M1r
SYSP 11, 50 # set system aperture value as 50mm fY| @{]rx
5^G7pI7
SYSP 201, 3 # set total wavelength number as 3 GV `idFd
SYSP 202, 1, 0.48613270 # set the 1st wavelength as 0.48613270 micron ?^e*UJNM
SYSP 202, 2, 0.58756180 # set the 2nd wavelength as 0.58756180 micron (E2lv#[
SYSP 202, 3, 0.65627250 # set the 3rd wavelength as 0.65627250 micron )W_ Y3M,
SYSP 203, 1, 1 # set the 1st wavelength weight as 1 RW| UQY#
SYSP 203, 2, 1 # set the 2nd wavelength weight as 1 '=@-aVp
SYSP 203, 3, 1 # set the 3rd wavelength weight as 1 "B_5Y&pM`
I1eb31<
SYSP 200, 2 # set the 2nd wavelength as the primary wavelength `Gy>tD.#V-
~m,mvRS
SYSP 100, 0 # set the field type as angle DYy@t^sC
SYSP 101, 3 # set the total field number as 3 .HH, l
SYSP 102, 1, 0 # set field 1 as x=0 degree brp N >\
SYSP 103, 1, 0 # set field 1 as y=0 degree "GIg| 3
SYSP 104, 1, 1 # set field 1 as weight=1 s5_ 1}KKCs
SYSP 102, 2, 0 # set field 2 as x=0 degree K284R=j -&
SYSP 103, 2, 3.5 # set field 2 as y=3.5 degree bUip p\[aV
SYSP 104, 2, 1 # set field 2 as weight=1 ThT.iD[
SYSP 102, 3, 0 # set field 3 as x=0 degree RP ScP
SYSP 103, 3, 5 # set field 3 as y=5 degree | r<.R >
SYSP 104, 3, 1 # set field 3 as weight=1 ;I0yQlx| U
g*"J10hyP
! set surface 1 as stop r&j+; JM5
STOPSURF 1 A_X^k|)T
]ci|$@V
! insert 3 surfcaces after stop 9v5.4a}
INSERT 2 {kY`X[fvZ
INSERT 2 $AL|d[[T[
INSERT 2 U3VsMV*Y
6832N 3=
! set surface parameters |?pYJk rYO
SURP 1, THIC, 275 # set surface 1 thickness as 275 do :RPZ!
`gA5P %
SURP 2, TYPE, "STANDARD" # set surface 2 type as "STANDARD",can be omitted Q>+_ W2~]
SURP 2, COMM, "front f1" # set surface 2 comment "~ i#9L/H
SURP 2, CURV, 1/600 # set surface 2 curvature as 1/600 6P/9Vh j'
SURP 2, THIC, 18 # set surface 2 thickness as 18 CO6XIgTe
SURP 2, GLAS, "BK7" # set surface 2 glass type as BK7 O7L6Htya
sov62wuqU
SURP 3, COMM, "back f1/front f2" # set surface 3 comment J[_?>YJ
SURP 3, CURV, -1/115 # set surface 3 curvature as -1/115 (t]R#2{
SURP 3, THIC, 18 # set surface 3 thickness as 18 _#\5]D~""
SURP 3, GLAS, "F2" # set surface 3 glass type as F2 ]>]H:NEq
3 ` C3+
SURP 4, COMM, "back f2" # set surface 4 comment %CfTqbB
SURP 4, CURV, -1/243 # set surface 4 curvature as -1/243 (HP={MrV
SURP 4, THIC, 395 # set surface 4 thickness as 395 aV0;WH_3
aX%g+6t2
UPDATE
|
|